Tilda Publishing
JOURNAL
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
ISSN 1028-978X (print)
ISSN 3033-733X (online)
PERSPEKTIVNYE
MATERIALY
Tilda Publishing
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ

2025, No. 6, abstracts

ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Multilayer coatings based on van der Waals MoS2/WS2/WSe2 heterostructures with improved antifriction properties

S. N. Grigoriev, D. V. Fominski, V. N. Nevolin, M. A. Volosova, V. Yu. Fominski

Multilayer coatings consisting of nanocrystals with layered atomic packing, in which planes with dense atomic packing are combined into a crystal through weak van der Waals interaction, were created by alternating pulsed laser ablation of MoS2 and WSe2 targets in vacuum conditions. Deposition on a substrate heated to 400 °C caused both the crystallization of the layers and the formation of the WS2 phase at the layer interfaces. As a result of the peculiarities of pulsed laser ablation of the selected targets, the van der Waals matrix of the layers contained metal nanoinclusions (bcc-Mo and β-W). The tribological properties were studied by sliding a steel ball over the coating at low relative humidity. The coefficient of sliding friction decreased with increasing load on the counterbody down to an ultra-low value of 0.01. The friction caused some disordering of the crystalline structure of the layers and mass transfer in the contact area of ​​the coating. The low value of the friction coefficient could be due to the difference in the packing parameters of atoms in the basal planes of molybdenum and tungsten dichalcogenides, accumulating in the tribofilm and determining the shear stresses of the atomic layers at local interfaces during counterbody sliding. Metallic nanoparticles could influence the tribo-activated modification of the nanostructure and the composition of the coating in the tribofilm.

Keywords: pulsed laser deposition, metal dichalcogenides, van der Waals structures, heterostructures, solid lubricants, friction coefficient.

DOI: 10.30791/1028-978X-2025-6-5-14
Grigoriev Sergey — Moscow State Technological University “STANKIN” (127055, Moscow, Vadkovsky per., 3a), Doctor of Eng. Sciences, professor, specialist in the field of high-tech methods of material processing and coating application. Email: sgrigor@mail.ru.
Fominski Dmitry — National Research Nuclear University MEPhI (115409, Moscow, Kashirskoe sh., 31), PhD in Engineering, research fellow, specialist in pulsed laser deposition of thin films and nanostructures. E-mail: dmitryfominski@gmail.com.
Nevolin Vladimir — National Research Nuclear University MEPhI (115409, Moscow, Kashirskoe sh., 31), Doctor of Physical and Mathematical sciences, professor, specialist in the field of physics of thin films and nanosystems. E-mail: vnnevolin@mephi.ru.
Volosova Marina — Moscow State Technological University “STANKIN” (127055, Moscow, Vadkovsky per. 3a), Doctor of Technical Sciences, associate professor, specialist in the field of highly effective methods for the formation of multifunctional coatings and the study of their properties. Email: m.volosova@stankin.ru.
Fominski Vyacheslav — National Research Nuclear University MEPhI (115409, Moscow, Kashirskoe sh., 31), Doctor of Physical and Mathematical sciences, professor, chief researcher, specialist in the field of thin film physics, nanostructures and beam technologies of surface modification. E-mail: vyfominskij@mephi.ru.
Reference citing:
Grigoriev S.N., Fominski D.V., Nevolin V.N., Volosova M.A., Fominski V.Yu. Mnogoslojnye pokrytiya na osnove van-der-vaal'sovyh geterostruktur MoS2/WS2/WSe2 s uluchshennymi antifrikcionnymi svojstvami [Multilayer coatings based on van der Waals MoS2/WS2/WSe2 heterostructures with improved antifriction properties]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 6, pp. 5 – 14. DOI: 10.30791/1028-978X-2025-6-5-14
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Thermoelectric micromodules for small heat flows

D. S. Nikulin, L. D. Ivanova, I. Yu. Nikhezina, A. G. Malchev

The parameters of micromodules for thermoelectric generators used at low heat fluxes and a cold junction temperature of 310 K are estimated. For the branches of micromodules, the authors consider their own developments of fine-crystalline materials based on Sb2Te3–Bi2Te3 solid solution p-type conductivity and Bi2Te3–Bi2Se3 solid solution n-type conductivity obtained by hot pressing and extrusion of powders prepared by grinding an ingot and methods of rapid crystallization of the melt: by spinning the melt and crystallization of the melt in a liquid. Higher power is obtained on modules whose branches are made of p- and n-type conductivity materials obtained by extrusion of granules prepared by crystallization of the melt in water. The dependences of the micromodule power on the temperature difference, thermoelectric properties (Seebeck coefficient, specific electrical conductivity and thermal conductivity) of the p- and n-branch materials, their number, cross section and height are calculated. It was found that with an increase in the cross-sectional area of the branches, the generated power of the module also increases. If the height of the branches increases, then the generated power of the micromodule decreases.

Keywords: thermoelectric generators, bismuth and antimony chalcogenides, energy characteristics of micromodules.

DOI: 10.30791/1028-978X-2025-6-15-23
Nikulin Dmitry — Baikov Institute of Metallurgy and Materials Sciences RAS (Moscow, 119334, Leninsky prospect, 49), senior researcher, specialist in the field of semiconductor materials science and research of properties of thermoelectric materials. E-mail: zaxnur@gmail.com.
Ivanova Lidia — Baikov Institute of Metallurgy and Materials Sciences RAS (Moscow, 119334, Leninsky prospect, 49), PhD (Eng. Sciences), leading researcher, specialist in the field of semiconductor materials science, technologies for obtaining and researching thermoelectric materials.
Nikhezina Irina — Baikov Institute of Metallurgy and Materials Sciences RAS (Moscow, 119334, Leninsky prospect, 49), researcher, specialist in the field of semiconductor materials science and research of properties of thermoelectric materials. E-mail: nihezina@imet.ac.ru.
Malchev Alexey — Baikov Institute of Metallurgy and Materials Sciences RAS (Moscow, 119334, Leninsky prospect, 49), junior researcher, specialist in the field of semiconductor materials science and research of properties of thermoelectric materials. E-mail: malchev@imet.ac.ru.
Reference citing:
Nikulin D.S., Ivanova L.D., Nikhezina I.Yu., Malchev A.G. Termoelektricheskie mikromoduli dlya malyh teplovyh potokov [Thermoelectric micromodules for small heat flows]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 6, pp. 15 – 23. DOI: 10.30791/1028-978X-2025-6-15-23
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Temperature dependencies of thermal properties of dielectric polymer composite materials based on hexagonal boron nitride and phenol-formaldehyde resin

E. A. Danilov, N. S. Romanov, E. M. Gurova, V. M. Samoilov

One of the main problems limiting effective operation of electronic devices is overheating. In order to provide effective heatsink in many applications, dielectric polymer composite materials should be used. Excellent dielectric and thermal properties, minimal thermal expansion considered, they should also provide stable properties throughout all temperature range of operation. In the present paper, temperature dependencies (25 – 200 °C range) of thermal conductivity, heat capacity, thermal diffusivity, and thermal expansion coefficient of hexagonal boron nitride/phenol-formaldehyde resin are considered. Most important dielectric properties — permittivity and dielectric loss tangent, — were also measured. Filler volume fraction varied from 5 to 85 %. Thermal diffusivity at highest filler fraction was 3.4 mm2/s (25 °C, ca. 2300 % improvement over neat polymer), thermal conductivity — 7.5 and 16.4 W/(m·K) in orthogonal directions being stable up to 200 °C. Agari – Uno model parameters (including filler anisotropic thermal conductivity) best fitting the system under study have been calculated. Conclusions on material composition providing optimal thermal, dielectric and thermo-mechanical properties for heatsink bulk thermal management electronic-grade composite, are made.

Keywords: polymer composite, thermal conductivity, heat capacity, hexagonal boron nitride, phenol-formaldehyde resin, thermal diffusivity, heatsink material, thermal interface material.

DOI: 10.30791/1028-978X-2025-6-24-37
Danilov Egor — Research Institute for Graphite-Based Structural Materials “NIIgrafit” (111524, 2 Elektrodnaya St., Moscow), PhD (Chem), head of department, specialist in physical chemistry and technologies of composite materials and nanomaterials. E-mail: danilovegor1@gmail.com.
Romanov Nikita — Research Institute for Graphite-Based Structural Materials “NIIgrafit” (111524, 2 Elektrodnaya St., Moscow), junior research fellow; D. Mendeleev University Chemical Technology of Russia (125047, Moscow, 9 Miusskaya sq.,), PhD student, specialist in composite technology, measurements of thermal and dielectric properties, e-mail: 533west484@gmail.com.
Gurova Ekaterina — Research Institute for Graphite-Based Structural Materials “NIIgrafit” (111524, 2 Elektrodnaya St., Moscow), junior research fellow, specialist in composite technology, measurements of thermal and dielectric properties. E-mail: km.gurova@gmail.com.
Samoilov Vladimir — Research Institute for Graphite-Based Structural Materials “NIIgrafit” (111524, 2 Elektrodnaya St., Moscow), Dr.Sci. in Engineering, chief research fellow, area of research: chemical technology of carbon-based and composite materials. E-mail: vsamoylov54grafit@yandex.ru.
Reference citing:
Fadeeva I.V., Mikhailova A.B., Davidova G.A., Akhmetov L.I., Antonova O.S., Churakova K.K., Selezneva I.I. Kompozicionnye poristye materialy iz polivinilpirrolidona i al'ginata natriya i dvojnogo (marganec i stroncij)-zameshchennogo trikal'cijfosfata dlya mediciny [Composite porous materials made of sodium alginate and double (manganese and strontium)-substituted tricalcium phosphate for medical applicatioms]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 6, pp. 38 – 45. DOI: 10.30791/1028-978X-2025-6-38-45
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Composite porous materials made of sodium alginate and double (manganese and strontium)-substituted tricalcium phosphate for medical applicatioms

I. V. Fadeeva, A. B. Mikhailova, G. A. Davidova, L. I. Akhmetov,
O. S. Antonova, K. K. Churakova, I. I. Selezneva

Porous composite materials with a matrix of a blend of polyvinylpyrrolidone (PVP) and sodium alginate (ALG) polymers, in which ceramic particles of double (manganese- and strontium)-substituted tricalcium phosphate (TCP) are distributed, have been developed. The XRD method showed that the main crystalline phase of (manganese- and strontium)-substituted TCP is whitlockite. As a result of in vitro studies, it was revealed that all the studied materials are not adhesive to cells and do not have a cytotoxic or inhibitory effect on them. Porous composite materials with a high rate of bioresorption of ceramic particles and a high potential for antibacterial activity and osteoinductive properties due to ion diffusion and changes in the properties of the surface layer can be used in reconstructive surgery to restore bone tissue function.

Keywords: mineral-polymer materials; wound dressings; sodium alginate, tricalcium phosphate.

DOI: 10.30791/1028-978X-2025-6-38-45
Fadeeva Inna — Baikov Institute of Metallurgy and Materials Science (119334, Moscow, Leninsky avenue, 49), leading researcher, PhD (Chem), specialist in the field of inorganic chemistry and medical materials science. E-mail: fadeeva_inna@mail.ru.
Mikhailova Alexandra — Baikov Institute of Metallurgy and Materials Science (119334, Moscow, Leninsky avenue, 49), researcher, PhD (Eng), specialist in the field of X-ray phase analysis. E-mail: sasham1@mail.ru.
Davydova Galina — Institute of Theoretical and Experimental Biophysics of RAS (142290, Pushchino, Moscow Region, Institutskaya St., 3), senior researcher, specialist in cell culture growth. E-mail: davidova_g@mail.ru.
Akhmetov Lenar — Institute of Biochemistry and Physiology of Microorganisms named after G.K. Skryabin; Institute of Mathematics of RAS (142290, Pushchino, Moscow Region, Institutskaya Street, 7), researcher fellow, specialist in biotechnology. E-mail: lenarakhmetov@yandex.ru.
Antonova Olga — Baikov Institute of Metallurgy and Materials Science (119334, Moscow, Leninsky avenue, 49), junior researcher, specialist in the field of microscopy. E-mail: osantonova@yandex.ru.
Churakova Kristina — Moscow State University, Faculty of Materials Science (119991, Moscow, Leninskie Gory, 1,), student, specialist in medical materials science. E-mail: comelkar@gmail.com.
Selezneva Irina — Institute of Theoretical and Experimental Biophysics of the RAS (142290, Pushchino, Moscow Region, Institutskaya St., 3), head of laboratory of Cell and tissue growth, specialist in cell culture growth. E-mail: selezneva_i@mail.ru.
Reference citing:
Fadeeva I.V., Mikhailova A.B., Davidova G.A., Akhmetov L.I., Antonova O.S., Churakova K.K., Selezneva I.I. Kompozicionnye poristye materialy iz polivinilpirrolidona i al'ginata natriya i dvojnogo (marganec i stroncij)-zameshchennogo trikal'cijfosfata dlya mediciny [Composite porous materials made of sodium alginate and double (manganese and strontium)-substituted tricalcium phosphate for medical applicatioms]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 6, pp. 38 – 45. DOI: 10.30791/1028-978X-2025-6-38-45
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Structural, magnetic and electrical characteristics of La – Sr manganites depending on electronic configuration of manganese substituents and oxygen concentration

V. K. Karpasyuk, A. G. Badelin, D. I. Merkulov, S. Kh. Estemirova

Manganites La0.7Sr0.3Mn0.9Fe0.05Me0.05O3+γ (Me = Sc, Co) with different oxygen content (γ < 0, γ = 0, γ > 0) were synthesized. Corresponding values of γ were obtained by annealing of sintered samples at different oxygen pressures: 10–8 Pa, 10–1 Pa, 105 Pa, respectively. All synthesized manganites have rhombohedral structure and are characterized by small value of micro-distortions, which is associated with the formation of modulated structures. Microstructure of the samples is quite dense, with an average crystallites diameter of 3.9 ± 1.6 µm for scandium-containing manganite and 3.1 ± 1.3 µm for (Fe,Co)-substituted manganite. Unit cell parameters and electromagnetic characteristics of the latter indicate the presence of Co3+(3d6) ions in its composition. (Fe,Sc)-containing manganites have lower magnetization values, Curie points and a significantly lower metal-semiconductor transition temperature compared to those containing iron and cobalt. Current-voltage (I – V) characteristics of La0.7Sr0.3Mn0.9Fe0.05Sc0.05O3+γ and La0.7Sr0.3Mn0.9Fe0.05Co0.05O3+γ manganites with negative deviation from oxygen stoichiometry and stoichiometric exhibit negative differential resistance of S-type in certain temperature ranges, and I – V characteristics of (Fe,Co)-substituted manganite in magnetic field contain two S-shaped sections. Threshold switching fields and maximum values of negative differential resistance modulus of I – V characteristics at different temperatures are determined. (Fe,Sc)-substituted manganite with an excess oxygen content at 190 – 200 K exhibits voltage stabilization effect. I – V characteristic of (Fe,Co)-substituted manganite annealed in oxygen does not contain the sections with negative differential resistance.

Keywords: manganese substituents, electron shells, nonstoichiometry, microstructure, magnetization, Curie point, metal-semiconductor transition, types of current-voltage characteristics, negative differential resistance

DOI: 10.30791/1028-978X-2025-6-46-55
Karpasyuk Vladimir — Astrakhan Tatishchev State University (20a Tatishchev Str., Astrakhan, 414056), Dr Sci. (Phys-Math), professor, chief researcher, specialist in the field of the physics of magnetic materials, semiconductors and dielectrics. E-mail: vkarpasyuk@mail.ru.
Badelin Alexey — Astrakhan Tatishchev State University (20a Tatishchev Str., Astrakhan, 414056), PhD (Phys-Math), leading researcher, specialist in the condensed matter physics and ceramic processing. E-mail: alexey_badelin@mail.ru.
Merkulov Denis — Astrakhan Tatishchev State University (20a Tatishchev Str., Astrakhan, 414056), PhD (Phys-Math), associate professor of the department, specialist in the field of condensed matter physics, materials science for semiconductors and dielectrics. E-mail: merkul_d@mail.ru.
Estemirova Svetlana — Institute of metallurgy, Ural Division of RAS (101 Amundsen Str., Ekaterinburg, 620016), PhD (Chem), senior researcher, specialist in condensed matter chemistry and X-ray structural analysis. E-mail: esveta100@mail.ru.
Reference citing:
Karpasyuk V.K., Badelin A.G., Merkulov D.I., Estemirova S.Kh. Strukturnye, magnitnye i elektricheskie harakteristiki La – Sr manganitov v zavisimosti ot elektronnoj konfiguracii zamestitelej marganca i soderzhaniya kisloroda [Structural, magnetic and electrical characteristics of La – Sr manganites depending on electronic configuration of manganese substituents and oxygen concentration]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 6, pp. 46 – 55. DOI: 10.30791/1028-978X-2025-6-46-55
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Martensitic transformations and inelastic properties of TiNi-based alloy
after abc pressing at 300 °C

A. A. Gusarenko, A. I. Lotkov, V. N. Grishkov, D. Y. Zhapova, D. I. Bobrov

The paper studies the effect of multi-axial forging (abc pressing) at 300 °C on the temperatures of martensitic transformations and inelastic properties (superelasticity and shape memory effects) of Ti49.8Ni50.2 (at. %) alloy samples. It is found that after abc pressing, the starting temperature of the B2→R direct martensitic transformation remains virtually unchanged and is equal to 63±1 ºС. At the same time, the finishing temperature of the direct martensitic transformation in B19′ structure decreases by 41 ± 1 °С; the temperatures of the start and finish of the B19′→B2 reverse martensitic transformation decrease by 18 and 13 degrees, respectively. The results demonstrate that after abc pressing at 300 °C, the alloy samples retain their inelastic properties and their value (regardless of given true strain) is comparable with the value of the inelastic properties of the samples in the coarse-grained state. It is shown that in all the studied samples the maximum value of reversible inelastic strain reaches ~ 18 % and is observed at 16 – 24 % of the plastic torsional strain specified for the samples.

Keywords: martensitic transformations, severe plastic deformation, abc pressing, shape memory effect.

DOI: 10.30791/1028-978X-2025-6-56-67
Gusarenko Angelina — Institute of Strength Physics and Materials Science of Siberian Branch of the Russian Academy of Sciences (2/4, pr. Akademicheskii, Tomsk, 634055), junior researcher, specialist in the field of condensed matter physics and materials science of shape memory alloys. E-mail: aag@ispms.ru.
Lotkov Aleksandr — Institute of Strength Physics and Materials Science of Siberian Branch of the Russian Academy of Sciences (2/4, pr. Akademicheskii, Tomsk, 634055), Doctor of Science in Physics and Mathematics, professor, chief researcher, specialist in the field of: physics of phase transformations, metal science of shape memory alloys, nanostructured materials science, surface and thin film physics. E-mail: lotkov@ispms.ru.
Grishkov Victor — Institute of Strength Physics and Materials Science of Siberian Branch of the Russian Academy of Sciences (2/4, pr. Akademicheskii, Tomsk, 634055), PhD in Physics and Mathematics, leading researcher, specialist in the field of phase transformations in metals and alloys, and metal science of shape memory alloys. E-mail: grish@ispms.ru.
Zhapova Dorzhima — Institute of Strength Physics and Materials Science of Siberian Branch of the Russian Academy of Sciences (2/4, pr. Akademicheskii, Tomsk, 634055), PhD of Physics and Mathematics, researcher, specialist in the field of metal science of shape memory alloys. E-mail: dorzh@ispms.ru.
Bobrov Dmitrii — Institute of Strength Physics and Materials Science of Siberian Branch of the Russian Academy of Sciences (2/4, pr. Akademicheskii, Tomsk, 634055), leading engineer, specialist in the field of condensed matter physics, phase transformation physics and materials science of shape memory alloys. E-mail: Chromium76@gmail.com.
Reference citing:
Gusarenko A.A., Lotkov A.I., Grishkov V.N., Zhapova D.Y., Bobrov D.I. Martensitnye prevrashcheniya i neuprugie svojstva splava na osnove TiNi posle abc pressovaniya pri 300 °S. [Martensitic transformations and inelastic properties of TiNi-based alloy after abc pressing at 300 °C]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 6, pp. 56 – 67. DOI: 10.30791/1028-978X-2025-6-56-67
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Regularities in the synthesis of zinc oxide nanoparticles
in an aqueous medium by laser ablation

I. N. Lapin, E. A. Gavrilenko, V. A. Svetlichnyi, A. I. Mamaev

The mechanism of transition of colloidal zinc metal nanoparticles obtained by pulsed laser ablation (PLA) of a metal target in liquid with different pH into zinc oxide during PLA process and their storage is considered. It is shown that the oxidation rate of zinc metal particles in solution depends on the rate of two partial electrochemical reactions interconnected by the electron balance, namely, the rate of the ionized zinc formation and the ionization of oxygen dissolved in water. It is revealed that the rate of oxygen delivery through the Prandtl boundary layer is the limiting stage of the zinc oxide phase formation process. Also, as a result of PLA of zinc target in weakly acidic, neutral and alkaline aqueous media and drying of the resulting colloidal solutions, a number of powder samples were obtained and their composition was analyzed. According to X-ray diffraction analysis, exposure to atmospheric oxygen resulted in significant oxidation of the obtained powders, but the metallic phase was detected in the sample obtained in an alkaline solution. Thus, varying experimental conditions provides a wide range of possibilities for obtaining a final product with a specific composition and properties.

Keywords: pulsed laser ablation, zinc oxide, pH, partial reactions of oxidation processes

DOI: 10.30791/1028-978X-2025-6-68-78
Lapin Ivan — National Research Tomsk State University (634050, Tomsk, Lenin Ave., 36), research officer, specialist in the field of materials research by X-ray methods and microscopy. E-mail: 579937@bk.ru.
Gavrilenko Ekaterina — National Research Tomsk State University (634050, Tomsk, Lenin Ave., 36), research assistant, specialist in study of nanomaterials and biosensors by electrochemical methods. E-mail: gavrilenko2470@gmail.com.
Svetlichnyi Valery — National Research Tomsk State University (634050, Tomsk, Lenin Ave., 36), PhD (phys-math sciences), head of laboratory, specialist in the field of laser physics and laser-matter interaction. E-mail: v_svetlichnyi@bk.ru.
Mamaev Anatoly — National Research Tomsk State University (634050, Tomsk, Lenin Ave., 36), doctor of chemical sciences, professor, specialist in the study of physical and chemical processes occurring at a localization of high-energy flows at the interface. E-mail: aim1953@yandex.ru.
Reference citing:
Lapin I.N., Gavrilenko E.A., Svetlichnyi V.A., Mamaev A.I. Zakonomernosti polucheniya nanochastic oksida cinka v vodnoj srede metodom lazernoj ablyacii [Regularities in the synthesis of zinc oxide nanoparticles in an aqueous medium by laser ablation]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 6, pp. 68 – 78. DOI: 10.30791/1028-978X-2025-6-68-78
Made on
Tilda