Tilda Publishing
JOURNAL
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
ISSN 1028-978X (print)
ISSN 3033-733X (online)
PERSPEKTIVNYE
MATERIALY
Tilda Publishing
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ

2025, No. 7, abstracts

ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Strain sensitivity of conductivity of composites based on polypropylene and carbon nanotubes: experimental and numerical studies of the effect of glass fiber reinforcement

O. V. Lebedev, T. S. Kurkin, M. Yu. Yablokov, E. K. Golubev, A. N. Ozerin

In order to develop an effective method for investigating and predicting the deformation behavior of the electrical conductivity of conductive nanocomposite materials additionally reinforced with glass fibers, a numerical model was developed that takes into account the interrelationship of the properties of such composites at different scales of their structure. For the experimental verification of the developed multiscale model, composites based on polypropylene modified with multi-walled carbon nanotubes were fabricated. The resulting nanocomposites were additionally reinforced with layers of glass fabric, with the layers stacked in a 0°/90° pattern. This ensured the multiscale structure of the resulting composite material, as well as the isotropy of the electrical conductivity in the plane of the glass fabric in the composite. The uniaxial deformation of the fabricated glass fiber reinforced nanocomposites with simultaneous continuous measurement of their electrical resistance was carried out by experimental and numerical methods. The results of the numerical modeling were compared with the experimental data obtained for both the nanotube-filled polypropylene and the fabricated glass fiber-reinforced nanocomposites based on it. It was shown that the introduction of glass fiber into an electrically conductive nanocomposite increases the strain sensitivity of the electrical conductivity of the material under uniaxial deformation, which is adequately predicted by the proposed method of multiscale modeling, provided that the structural features of the composite are correctly reflected.

Keywords: nanocomposites; carbon nanotubes; polypropylene; glass fabric; multiscale modeling; electrical conductivity; conductivity strain sensitivity.

DOI: 10.30791/1028-978X-2025-7-5-17
Lebedev Oleg — Enikolopov Institute of Synthetic Polymeric Materials of the Russian Academy of Sciences (70 Profsoyuznaya St., Moscow 117393), Moscow Institute of Physics and Technology (9 Institutsky lane, Dolgoprudny 141700), PhD (Phys.-Math.), Senior Researcher, specialist in the field of numerical modeling of polymer composite materials. E-mail: oleg.lebedev@phytsech.edu.
Kurkin Tikhon — Enikolopov Institute of Synthetic Polymeric Materials of the Russian Academy of Sciences (70 Profsoyuznaya St., Moscow 117393), PhD (Phys.-Math.), Senior Researcher, specialist in the field of electron microscopy, experimental and numerical data processing. E-mail: t.kurkin@gmail.com.
Yablokov Mikhail — Enikolopov Institute of Synthetic Polymeric Materials, Russian Academy of Sciences (70 Profsoyuznaya St., Moscow 117393), PhD (Phys.-Math.), Senior Researcher, specialist in the field of experimental studies of structure and properties of polymers and composite materials. E-mail: yabl1@yandex.ru.
Golubev Evgeny — Enikolopov Institute of Synthetic Polymer Materials of the Russian Academy of Sciences (70 Profsoyuznaya St., Moscow 117393), Semenov Federal Research Center for Chemical Physics of the Russian Academy of Sciences (4 build. 1 Kosygina Street, Moscow 119991), research associate, specialist in processing of polymers and polymer composites. E-mail: jeckagolubev@gmail.com.
Ozerin Alexander — Enikolopov Institute of Synthetic Polymeric Materials of the Russian Academy of Sciences (70 Profsoyuznaya St., Moscow 117393), Dr. Sc. (Chem.), Corresponding Member of the Russian Academy of Sciences, Professor, Chief Researcher, specialist in the field of physics and chemistry of polymers and polymer composites. E-mail: ozerin@ispm.ru.
Reference citing:
Lebedev O.V., Kurkin T.S., Yablokov M.Yu., Golubev E.K., Ozerin A.N. Tenzorezistivnost' kompozitov na osnove polipropilena i uglerodnyh nanotrubok: eksperimental'nye i chislennye issledovaniya vliyaniya armirovaniya steklotkan'yu [Strain sensitivity of conductivity of composites based on polypropylene and carbon nanotubes: experimental and numerical studies of the effect of glass fiber reinforcement]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 7, pp. 5 – 17. DOI: 10.30791/1028-978X-2025-7-5-17
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Investigation of the influence of organic and inorganic plasticizing agents on the properties of alumina supports and CoMo/Al2O3 hydrotreating catalysts. Part 2. CoMo/Al2O3 hydrotreating catalysts based on alumina supports

P. P. Mukhacheva, Yu. V. Vatutina, K. A. Nadeina, I. G. Danilova, P. P. Dik,
V. P. Pakharukova, E. Yu. Gerasimov, I. P. Prosvirin, O. V. Klimov, A. S. Noskov

The influence of organic (acetic acid, citric acid, and diethylene glycol) and inorganic (nitric acid and ammonia) plasticizing agents for producing of alumina supports on the properties of CoMoP/Al2O3 catalysts based on them for hydrotreatment of diesel fractions has been investigated. Changing the textural characteristics of the supports by varying the plasticizing agent leads to different degrees of promotion of MoS2 particles by cobalt atoms, changes in the surface concentration of phosphorus, and changes in the morphology of the active component particles in the catalysts. Testing of catalysts in hydrotreating of model feedstock and straight-run diesel fraction showed that the largest number of cycles of dibenzothiophene conversion on the active center of the catalyst is achieved on the catalyst based on the carrier plasticized with ammonia solution, the smallest - on the catalyst based on the carrier prepared with the addition of diethylene glycol. In the series of samples CoMoP/Al-AcA → CoMoP/Al-NA → CoMoP/ Al-CA → CoMoP/Al-DEG, a dependence between the surface concentration of P and the Co content in the CoMoS phase was observed. The lower the surface concentration of P and the higher the Co content in the CoMoS phase, the higher the number of dibenzothiophene conversion cycles on the active center. The results of catalytic experiments on straight-run diesel fraction showed good agreement with the textural characteristics of the catalysts.

Keywords: plasticization; alumina; inorganic acid; organic acid; hydrotreating.

DOI: 10.30791/1028-978X-2025-7-18-34
Mukhacheva Polina — Boreskov Institute of catalysis SB RAS (Novosibirsk, 630090, pr. Lavrentieva 5), junior researcher of Boreskov Institute of Catalysis, Specialist in supports and catalysts for hydrotreating, their preparation and characterization. E-mail: mpp@catalysis.ru.
Vatutina Yuliya — Boreskov Institute of catalysis SB RAS (Novosibirsk, 630090, pr. Lavrentieva 5), researcher of Boreskov Institute of Catalysis, Specialist in supports and catalysts for hydrotreating, their preparation and characterization. E-mail: y.vatutina@catalysis.ru.
Nadeina Ksenia — Boreskov Institute of catalysis SB RAS (Novosibirsk, 630090, pr. Lavrentieva 5), senior researcher of Boreskov Institute of Catalysis, Specialist in supports and catalysts for hydrotreating, their preparation and characterization. E-mail: lakmallow@catalysis.ru.
Danilova Irina — Boreskov Institute of catalysis SB RAS (Novosibirsk, 630090, pr. Lavrentieva 5), senior researcher of Boreskov Institute of Catalysis, Specialist in the characterization of catalysts by IR and UV spectroscopy methods. E-mail: danig@catalysis.ru
Dik Pavel — Boreskov Institute of catalysis SB RAS (Novosibirsk, 630090, pr. Lavrentieva 5), researcher of Boreskov Institute of Catalysis, Specialist in supports and catalysts for hydrocracking, their preparation and characterization. E-mail: dik@catalysis.ru.
Pakharukova Vera — Boreskov Institute of catalysis SB RAS (Novosibirsk, 630090, pr. Lavrentieva 5), senior researcher of Boreskov Institute of Catalysis, Specialist in the characterization of supports and catalysts by XRD method. E-mail:
verapakharukova@yandex.ru.
Gerasimov Evgeniy — Boreskov Institute of catalysis SB RAS (Novosibirsk, 630090, pr. Lavrentieva 5), leading researcher of Boreskov Institute of Catalysis, Specialist in the characterization of materials research using HRTEM, SEM methods. E-mail: gerasimov@catalysis.ru.
Prosvirin Igor — Boreskov Institute of catalysis SB RAS (Novosibirsk, 630090, pr. Lavrentieva 5), senior researcher of Boreskov Institute of Catalysis, Specialist in the characterization of supports and catalysts by XPS method. E-mail: prosvirin@catalysis.ru.
Klimov Oleg — Boreskov Institute of catalysis SB RAS (Novosibirsk, 630090, pr. Lavrentieva 5), leading researcher of Boreskov Institute of Catalysis, Specialist in supports and catalysts for hydrotreating, their preparation and characterization. E-mail: klm@catalysis.ru
Noskov Alexander — Boreskov Institute of catalysis SB RAS (Novosibirsk, 630090, pr. Lavrentieva 5), corresponding member, Head of the Catalytic Process Technology Department of Boreskov Institute of Catalysis, Specialist in supports and catalysts for hydrotreating, their preparation and characterization. E-mail: noskov@catalysis.ru.
Reference citing:
Mukhacheva P.P., Vatutina Yu.V., Nadeina K.A., Danilova I.G., Dik P.P., Pakharukova V.P., Gerasimov E.Yu., Prosvirin I.P., Klimov O.V., Noskov A.S. Issledovanie vliyaniya organicheskih i neorganicheskih plastificiruyushchih agentov na svojstva alyumooksidnyh nositelej i CoMo/Al2O3 katalizatorov gidroochistki. CHast' 2. CoMo/Al2O3 katalizatory gidroochistki na osnove alyumooksidnyh nositelej. [Investigation of the influence of organic and inorganic plasticizing agents on the properties of alumina supports and CoMo/Al2O3 hydrotreating catalysts. Part 2. CoMo/Al2O3 hydrotreating catalysts based on alumina supports]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 7, pp. 18 – 34. DOI: 10.30791/1028-978X-2025-7-18-34
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Study of the properties of nanocomposites based on a mixture of high and low pressure polyethylene with cobalt-containing nanofillers

G. G. Mamedova, N. I. Kurbanova, T. M. Gulieva, E. G. Iskenderova

Composite materials based on a mixture of high- and low-pressure polyethylene, including additives of finely dispersed cobalt oxide, have been studied by X-ray phase (XRD), differential thermal analysis (DTA) and scanning electron microscopy (SEM). An improvement in the strength, deformation parameters and thermal oxidative stability of the composite was revealed with the introduction of finely dispersed cobalt oxide, which, apparently, is due to the formation of interfacial bonds between cobalt-containing nanoparticles and components of the polymer composition. It has been shown that nanocomposites based on a mixture of high- and low-density polyethylenes, including additives of finely dispersed cobalt oxide, can be processed both by pressing and by injection molding and extrusion, which expands the scope of their applications. Small amounts of nanofiller introduced into the polymer play the role of structure formers — artificial crystallization nuclei, which contributes to the appearance of a fine spherulite structure in the polymer, characterized by enhanced physical, mechanical and thermal properties of the resulting nanocomposite.

Keywords: high pressure polyethylene; low-pressure polyethylene; metal-containing composites; cobalt oxide nanoparticles; strength properties; deformation properties; thermal properties; XRD, DTA and SEM analyses.

DOI: 10.30791/1028-978X-2025-7-35-42
Mamedova Gunay Huseyn qizi — PhD student, Azerbaijan State Oil and Industry University (Baku, Azerbaijan, Az1010, avenue Azadliq20), specialist in the field of development of composition materials. E-mail: ipoma@science.az.
Kurbanova Nushaba Ismail qizi — Institute of Polymer Materials of Ministry of Science and Education Republic of Azerbaijan (Sumgait, Azerbaijan, Az5004, S.Vurgun Str, 124), Dr Sc. (Chem.), head of laboratory, specialist in the field of development of composition materials and also nanocomposites on the basis of elastomers and thermoplasts and their binary mixtures. E-mail: ipoma@science.az; kurbanova.nushaba@mail.ru.
Gulieva Turkan Mushvig qizi — Institute of Polymer Materials of Ministry of Science and Education Republic of Azerbaijan, (Sumgait, Azerbaijan, Az5004, S.Vurgun Str, 124), junior researcher, specialist in the field of development of composition materials. E-mail: ipoma@science.az
Isgadarova Esfira Gudrat qizi — Institute of Polymer Materials of Ministry of Science and Education Republic of Azerbaijan (Sumgait, Azerbaijan, Az5004, S.Vurgun Str, 124), engineer, specialist in the field of development of composition materials. E-mail: ipoma@science.az.
Reference citing:
Mamedova G.G., Kurbanova N.I., Gulieva T.M., Iskenderova E.G. Issledovanie svojstv nanokompozitov na osnove smesi polietilenov vysokogo i nizkogo davleniya s kobal'tsoderzhashchimi nanonapolnitelyami [Study of the properties of nanocomposites based on a mixture of high and low pressure polyethylene with cobalt-containing nanofillers]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 7, pp. 35 – 42. DOI: 10.30791/1028-978X-2025-7-35-42
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Methods for increasing the compressive strength of glassy carbon foams

D. V. Ponomareva, E. I. Timoshchuk

The work proposes methods for producing glassy carbon foams with increased compressive strength. The influence of the gas environment during carbonization on the structural characteristics of glassy carbon foams was shown. X-ray diffraction (XRD), Raman spectroscopy and scanning electron microscopy (SEM) were used to analyze the influence of the gas environment during carbonization and coating. The compressive strength was determined by stress-strain tests. It has been shown that when the carbonization process is carried out in an inert environment, the defectiveness of the structure of glassy carbon foams is lower compared to materials obtained in a reducing environment. The compressive strength of samples that underwent carbonization in an inert and reducing environment is 0.57 – 0.83 MPa and 0.27 – 0.55 MPa, respectively. It has been established that the application of a low-temperature pyrocarbon coating using the CVI method leads to an increase in the compressive strength of glassy carbon foams that have undergone carbonization in an inert environment to values of 0.91 – 1.8 MPa.

Keywords: glassy carbon foams, carbonization, pyrocarbon coating, compressive strength.

DOI: 10.30791/1028-978X-2025-7-43-54
Ponomareva Daria — Joint Stock Company “Research Institute of Structural Materials Based on Graphite “NIIgrafit” (Moscow, 111524, Electrodnaya st., 2, building 1), senior researcher, specialist in the field of carbon materials and additive technologies. E-mail: DVPonomareva@rosatom.ru
Timoshchuk Elena — Joint Stock Company “Research Institute of Structural Materials Based on Graphite “NIIgrafit” (Moscow, 111524, Electrodnaya st., 2, building 1), Candidate of Technical Sciences, Head of laboratory, specialist in the field of carbon materials and additive technologies. E-mail: E-mail: EITimoschuk@rosatom.ru.
Reference citing:
Ponomareva D.V., Timoshchuk E.I. Sposoby povysheniya predela prochnosti pri szhatii steklouglerodnyh pen [Methods for increasing the compressive strength of glassy carbon foams]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 7, pp. 43 – 54. DOI: 10.30791/1028-978X-2025-7-43-54
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Study of the effect of printing orientation by Fused Deposition Modeling on polymer composite mechanical properties

A. V. Babaytsev, S. A. Shumskaya

The results of research of physical and mechanical properties of commercially available in the Russian market composite filaments based on ABS, nylon and polyurethane polymers with addition of discrete fillers such as glass (GF) and carbon (CF) with their different percentages are presented. Tensile tests were performed on the samples produced by layer-by-layer deposition (FDM) with different orientation of layer layup direction of 0° (horizontal) and 90° (vertical). It was observed that the printing strategy of horizontally oriented specimens created interlayer weaknesses that caused their failure during testing. It was found that vertically printed specimens were inferior to horizontally printed specimens in strength and generally in ductility. The exception is GF-30% polyurethane, which demonstrated higher strength and stiffness in the horizontal orientation but lower ductility compared to the vertically printed specimens. Glass-filled nylon CF-20% proved to be an unstable material as evidenced by the high coefficient of variation of its parameters. ABS CF-12% specimens showed minimal differences between vertical and horizontal orientations, but the vertical modulus of elasticity was characterized by a high coefficient of variation. The experimental results emphasize the need for careful selection of print and material orientation depending on the required mechanical performance.

Keywords: polymer composites, FDM, glass fiber, carbon fiber, physical and mechanical properties, tensile strength.

DOI: 10.30791/1028-978X-2025-7-55-61
Babaytsev Arseniy — Moscow Aviation Institute (National Research University) (Moscow, 125993, Volokolamskoe highway, 4), PhD, Associate Professor, Senior Researcher, specialist in physical and mechanical testing. E-mail: ar77eny@gmail.com.
Shumskaya Sofia — Moscow Aviation Institute (National Research University) (Moscow, 125993, Volokolamskoe highway, 4), postgraduate student, Junior Researcher, additive technology specialist. E-mail: bratinaaa@gmail.com.
Reference citing:
Babaytsev A.V., Shumskaya S.A. Issledovanie vliyaniya orientacii pechati metodom poslojnogo naplavleniya na mekhanicheskie svojstva polimernyh kompozicionnyh materialov [Study of the effect of printing orientation by Fused Deposition Modeling on polymer composite mechanical properties]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 7, pp. 55 – 61. DOI: 10.30791/1028-978X-2025-7-55-61
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Flame spray synthesis of yttrium oxide powders for transparent ceramics

T. O. Evstropov, S. S. Balabanov, D. Yu. Kosyanov, Jiang Li

The paper studies the effect of urea concentration and yttrium nitrate:urea ratio on the morphology and particle size distribution of yttrium oxide powders synthesized by flame spray pyrolysis. Particles with a median size of 400 to 1300 nm are obtained. Thermodynamic modeling of the precursor combustion reaction is performed, and the stages of decomposition of aqueous solutions of yttrium nitrates with urea and glycine are studied using differential scanning calorimetry (DSC). It is found that the type of reducing agent affects the morphology of the particles due to differences in the mechanisms of precursor decomposition. Vacuum sintering of the synthesized powders made it possible to obtain Y2O3 ceramics with a grain size of 8.2 – 9 μm.

Keywords: flame spray pyrolysis, transparent ceramics, yttria, thermodynamic modelling.

DOI: 10.30791/1028-978X-2025-7-62-74
Evstopov Timofey — Institute of Chemistry of High-Purity Substances of the Russian Academy of Sciences (ICHPS RAS) (Nizhny Novgorod, Tropinina st. 49), junior researcher, specialist in field of transparent ceramics. E-mail: evstropov@ihps-nnov.ru.
Balabanov Stanislav — Institute of Chemistry of High-Purity Substances of the Russian Academy of Sciences (ICHPS RAS) (Nizhny Novgorod, Tropinina st. 49), PhD, leading researcher, specialist in field of transparent ceramics. E-mail: balabanov@ihps-nnov.ru.
Kosyanov Denis — Far Eastern Federal University (Vladivostok, Primorsky Krai, Russky Island, Ajax, 10), PhD, professor of department of industrial safety. E-mail: kosianov.diu@dvfu.ru
Li Jiang — Shanghai Institute of Ceramics, Chinese Academy of Sciences, Transparent Ceramics Research Center (Shanghai, China), PhD, professor. E-mail: lijiang@mail.sic.ac.cn.
Reference citing:
Evstropov T.O., Balabanov S.S., Kosyanov D.Yu., Li Jiang Sintez poroshkov oksida ittriya szhiganiem aerozolya v plameni dlya polucheniya opticheskoj keramiki [Flame spray synthesis of yttrium oxide powders for transparent ceramics]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 7, pp. 62 – 74. DOI: 10.30791/1028-978X-2025-7-62-74
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Study of effect of vanadium interlayer on structure and mechanical properties of AlMg6 – Vanadiun – 12Cr18Ni10Ti obtained by explosive welding

A. Yu. Malakhov, N. N. Niyozbekov, I. V. Denisov, D. V. Shakhray,
V. A. Sosikov, O. D. Boyarchenko, V. O. Kopytskiy

In this work, a multilayer composite material AMg6 – VnPl-1(vanadium) – 12Cr18Ni10Ti was obtained using explosive welding. The results of a study of the explosive welding process using high-speed photography showed that, during the collision of layers, vertical oscillations of the intermediate vanadium layer occur, which lead to a change in the height of welding gaps between welded layers. In turn, this change in gap height causes sharp disturbances in the propagation of shock-compressed gas, leading to changes in its geometric and thermodynamic parameters, negatively affecting the stability of joint formation.

Keywords: explosive welding, shock-compressed gas, weld interface, microstructure, mechanical properties.

DOI: 10.30791/1028-978X-2025-7-75-84
Malakhov Andrey — Merzhanov Institute of Structural Macrokinetics and Materials Science of the Russian Academy of Sciences (Chernogolovka, 142432, Akademika Osipyan str., 8), Ph.D., Senior researcher, expert in the field of explosive welding and materials science. E-mail: sir.malahov2009@yandex.ru.
Niyozbekov Nemat — Merzhanov Institute of Structural Macrokinetics and Problems of Materials Science of the Russian Academy of Sciences (Chernogolovka, 142432, Akademika Osipyan str., 8), junior researcher, expert in the field of explosive welding. E-mail: nemat199595@mail.ru.
Denisov Igor — Merzhanov Institute of Structural Macrokinetics and Materials Science of the Russian Academy of Sciences (Chernogolovka, 142432, Akademika Osipyan str., 8), Ph.D., Senior researcher, expert in the field of explosion welding and materials science. E-mail: ingener.denisov@yandex.ru.
Shakhray Denis — Federal Research Center of Problems of Chemical Physics and Medical Chemistry of the Russian Academy of Sciences (Chernogolovka, 142432, Akademika Semenova Avenue, 1), Ph.D., Head of the Department of Extreme States of Matter, expert in the field of shock wave physics and registration of fast-flowing processes. E-mail: shakhray@icp.ac.ru.
Sosikov Vasily — Federal Research Center of Problems of Chemical Physics and Medical Chemistry of the Russian Academy of Sciences (Chernogolovka, 142432, Akademika Semenova Avenue, 1), Ph.D., expert in chemical physics, including combustion and explosive physics. E-mail: vaso@icp.ac.ru.
Boyarchenko Olga — Merzhanov Institute of Structural Macrokinetics and Materials Science of the Russian Academy of Sciences (Chernogolovka, 142432, Akademika Osipyan str., 8), Ph.D., junior researcher, expert in chemical physics, combustion and explosive, physics of extreme states of matter. E-mail: olgaboyarchenko@gmail.com.
Kopytsky Vladislav — Merzhanov Institute of Structural Macrokinetics and Materials Science of the Russian Academy of Sciences (Chernogolovka, 142432, Akademika Osipyan str., 8), junior researcher, expert in materials science. E-mail: kvo@ism.ac.ru.Bondarenko Gennady — National Research University Higher School of Economics (101000, Russia, Moscow, Myasnitskaya St., 20), Dr.Sc. (Phys.-Math.), Distinguished Professor; Research Institute of Advanced Materials and Technologies (105187, Russia, Moscow, Shcherbakovskaya St., 53), deputy director, specialist in the field of condensed matter physics. E-mail: bondarenko_gg@rambler.ru.
Gaydar Anna — Research Institute of Advanced Materials and Technologies (105187, Russia, Moscow, Shcherbakovskaya St., 53), PhD (Phys.-Math.), leading researcher, specialist in the field of electron microscopy and elemental microanalysis. E-mail: a_i_g@bk.ru.
Matveev Egor — Research Institute of Advanced Materials and Technologies (105187, Russia, Moscow, Shcherbakovskaya St., 53), PhD (Eng.), senior researcher, specialist in the field of investigation of physical and mechanical properties of materials. E-mail: maegor@gmail.com.
Reference citing:
Malakhov A.Yu., Niyozbekov N.N., Denisov I.V., Shakhray D.V., Sosikov V.A., Boyarchenko O.D., Kopytskiy V.O. Issledovanie vliyaniya promezhutochnogo sloya iz vanadiya na obrazovanie soedineniya AMg6-Vanadij-12H18N10T v processe svarki vzryvom [Study of effect of vanadium interlayer on structure and mechanical properties of AlMg6 – Vanadiun – 12Cr18Ni10Ti obtained by explosive welding] . Perspektivnye Materialy [Advanced Materials] (in Russ), 2025, no. 7, pp. 75 – 84. DOI: 10.30791/1028-978X-2025-7-75-84
ПЕРСПЕКТИВНЫЕ МАТЕРИАЛЫ
Changes in the contact properties of composites based on ultra-high molecular weight polyethylene and nanosized carbon fillers under the influence of low-temperature plasma

M. S. Piskarev, O. V. Lebedev, Е. P. Tikunova, Е. К. Golubev, Т. S. Kurkin,
A. B. Gilman, A. A. Kuznetsov, A. N. Ozerin

In this study the contact properties (wettability, surface energy) of composite material samples before and after exposure to low-temperature plasma, storage for 7 days, and isothermal heating at 100°C for 30 minutes, were investigated. The samples were obtained by solid-state processing of mixtures of ultra-high-molecular-weight polyethylene reactor powder and nanoscale carbon fillers (electrically conductive carbon black (CB), nanodiamond soot, and graphite nanoplatelets) with a filler content ranging from 1 to 20 wt.%. It was shown that plasma treatment leads to a unification of the contact properties of the composite samples regardless of the type and amount of filler, whereas storage and heating also result in changes in the contact properties of the composite surfaces. Samples filled with CB exhibited the most pronounced dependence of surface properties on the filler content in the composite.

Keywords: composite materials, carbon nanoparticles, carbon black, nanodiamond soot, low-temperature plasma, contact properties.

DOI: 10.30791/1028-978X-2026-11-76-84
Piskarev Mikhail — Enikolopov Institute of Synthetic Polymer Materials Russian Academy of Siences (117393, Moscow, Profsoyuznaya str, 70), PhD (Chem.), senior researcher, specialist in the field of plasma chemistry. E-mail: mikhailpiskarev@gmail.com.
Lebedev Oleg — Enikolopov Institute of Synthetic Polymer Materials Russian Academy of Siences (117393, Moscow, Profsoyuznaya str, 70), PhD (Phys.-Math.), senior researcher, specialist in polymer and composite materials. E-mail: oleg.lebedev@phytsech.edu.
Tikunova Ekaterinaа — Enikolopov Institute of Synthetic Polymer Materials Russian Academy of Siences (117393, Moscow, Profsoyuznaya str, 70), junior researcher, specialist in polymer materials and the processing of polymer composites. E-mail: etikunova@gmail.com
Golubev Evgeni — Enikolopov Institute of Synthetic Polymer Materials Russian Academy of Siences (117393, Moscow, Profsoyuznaya str, 70), junior researcher, specialist in polymer materials and the processing of polymer composites. E-mail: golubev@ispm.ru.
Kurkin Tichon — Enikolopov Institute of Synthetic Polymer Materials Russian Academy of Siences (117393, Moscow, Profsoyuznaya str, 70), Senior Researcher, PhD of Physical and Mathematical Sciences, specialist in the field of polymer materials and crystallography. E-mail: t.kurkin@gmail.com
Gilman Alla — Enikolopov Institute of Synthetic Polymer Materials Russian Academy of Siences (117393, Moscow, Profsoyuznaya str, 70), PhD (Chem), assistant professor, senior researcher, specialist in the field of plasma chemistry. E-mail: plasma@ispm.ru, gilmanab@gmail.com.
Kuznetsov Alexander — Enikolopov Institute of Synthetic Polymer Materials Russian Academy of Siences (117393, Moscow, Profsoyuznaya str, 70), Dr.Sc. (Chem.), professor, laboratory manager, specialist in polymer chemistry. E-mail: kuznets24@yandex.ru.
Оzerin Alexander — Enikolopov Institute of Synthetic Polymer Materials Russian Academy of Siences (117393, Moscow, Profsoyuznaya str, 70), Dr.Sc. (Chem.), Sciences Scientific Director of the Institute, Corresponding Member of the Russian Academy of Sciences, specialist in the fields of polymer materials, composite processing, and crystallography. E-mail: ozerin@ispm.ru.
Reference citing:
Piskarev M.S., Lebedev O.V., Tikunova Е.P., Golubev Е.К., Kurkin Т.S., Gilman A.B., Kuznetsov A.A., Ozerin A.N. Izmenenie kontaktnyh svojstv kompozitov na osnove sverhvysokomolekulyarnogo polietilena i nanorazmernyh uglerodnyh napolnitelej pod vozdejstviem nizkotemperaturnoj plazmy [Changes in the contact properties of composites based on ultra-high molecular weight polyethylene and nanosized carbon fillers under the influence of low-temperature plasma]. Perspektivnye Materialy [Advanced Materials] (in Russ), 2026, no. 11, pp. 76 – 84.
Made on
Tilda